Configuring 2 Lan Into Same Subnet Over Wan Cisco Community Can i route everything from r1 to r2 and r2 to r1 to let pc and devices from network 1 communicate with network 2? or how should i configure the routers to let network 1 communicate with network 2?. So while you can't have two interfaces with the same address (overlapping subnets), you can have one interface in two subnets using a cisco router feature called secondary ip addressing which odom says isn't used very much.
Solved Same Subnet Between Wan Link Cisco Community You have two independent ip ranges, 192.168.1.0–192.168.1.255 for router 1, and 192.168.2.0–192.168.2.127 for router 2. that's already good enough and you don't need to do any "lower part upper part" stuff. We need to configure one subnet in both locations and have this subnet spanned across the wan. the reason for this is we have a security system that needs to monitor both sites using a private ip subnet. the security servers can be connected to 3750 switches in both locations. If a gateway device is not provided, the packet will never leave that network id segment and will time out. this is why two joined routers must have the same network id on the connecting interfaces. any other configuration would be “goofy” and cause problems down the road. Hi i have recently purchase cisco rv042 router and i want it with my existing network. my firewall ip is 10.85.16.1 and im giving 10.85.16.201 rv042 wan1 and i want 10.85.16.2 on lan of rv042 router but when im giving both ip internet does not work.
Lan To Lan Communication Using Same Subnet Between 2 Locations Cisco Community If a gateway device is not provided, the packet will never leave that network id segment and will time out. this is why two joined routers must have the same network id on the connecting interfaces. any other configuration would be “goofy” and cause problems down the road. Hi i have recently purchase cisco rv042 router and i want it with my existing network. my firewall ip is 10.85.16.1 and im giving 10.85.16.201 rv042 wan1 and i want 10.85.16.2 on lan of rv042 router but when im giving both ip internet does not work. It describes the encapsulation protocols used for routing between vlans and provides some basic information about designing vlans. this module contains tasks for configuring routing between vlans. For example, i have multiple hosts behind a nat router using pat. then, a customer comes back and wants to rdp into one of the hosts. assign a second ip address to the wan port of the router and set up static nat to this address. Run one cable from the switch to wan1. run a second cable to wan2 on your meraki. assign public ip 1 to wan1, assign public ip 2 to wan2. there is a small chance the meraki doesn't like 2 wan interfaces using ip's on the same subnet, but i believe it should work. If both ip addresses are in the same subnet then there is only one wan connection that they are providing with multiple ips and or ports. for true redundancy you need two different subnets so you can setup either failover, round robin, or bandwidth percentage routing to the secondary wan.
Lan And Wan Interface Connected In The Same Switch Core Cisco Community It describes the encapsulation protocols used for routing between vlans and provides some basic information about designing vlans. this module contains tasks for configuring routing between vlans. For example, i have multiple hosts behind a nat router using pat. then, a customer comes back and wants to rdp into one of the hosts. assign a second ip address to the wan port of the router and set up static nat to this address. Run one cable from the switch to wan1. run a second cable to wan2 on your meraki. assign public ip 1 to wan1, assign public ip 2 to wan2. there is a small chance the meraki doesn't like 2 wan interfaces using ip's on the same subnet, but i believe it should work. If both ip addresses are in the same subnet then there is only one wan connection that they are providing with multiple ips and or ports. for true redundancy you need two different subnets so you can setup either failover, round robin, or bandwidth percentage routing to the secondary wan.
Comments are closed.